Aux Heat Vs. Em Heat: What It Means for Your Energy Use

Aux Heat and Em Heat are both backup heating functions for a heat pump, but they do not mean the same thing. Aux Heat usually turns on automatically when your heat pump needs help meeting the temperature you selected. Em Heat is generally a manual setting used when the outdoor heat pump cannot operate properly.

Across the Puget Sound region, winter weather is often mild enough for heat pumps to heat efficiently. Still, cold snaps, damp conditions, defrost cycles, and large thermostat changes can bring on backup heat. Knowing what your auxiliary heat thermostat is telling you can help you protect comfort while avoiding unnecessary electricity use.

Aux Heat Supports Your Heat Pump in Cold Weather

Auxiliary heat is supplemental heat that works alongside your outdoor heat pump. In many all-electric systems, it comes from electric heat strips inside the indoor air handler. Some homes use a different backup setup, so we recommend checking your system documentation or asking a technician if you are unsure what powers your backup heat.

Your thermostat may show Aux Heat when the system needs extra help, including during:

  • A large gap between the indoor temperature and your thermostat setting
  • Recovery after a deep overnight temperature setback
  • Colder outdoor weather that increases heating demand
  • A normal defrost cycle for the outdoor unit

During defrost, a heat pump briefly changes operation to clear frost from its outdoor coil. Backup heat helps keep the air coming from your vents from feeling cool while that happens.

A short Aux Heat message is not automatically a warning sign. We pay closer attention when it stays on for long periods in moderate weather, appears often without an obvious reason, or comes with weak airflow, cold rooms, or uneven heating.

Em Heat Is a Backup Mode, Not a Daily Setting

Emergency Heat, often shown as Em Heat, is different from Aux Heat. This setting typically turns off the outdoor heat pump and relies only on the backup heat source. It may be used temporarily if the outdoor unit has failed, has visible damage, or cannot operate safely until it can be inspected.

The key difference is simple: Aux Heat is normally automatic and works with the heat pump. Em Heat is usually selected manually and bypasses the heat pump altogether. When electric heat strips are the backup source, Emergency Heat can use much more electricity because the system is no longer moving heat from outdoors.

We do not recommend switching to Em Heat just because Aux Heat appears on the display or because you want faster warmth. Use it only when a technician advises it or when the outdoor heat pump is clearly not operating and temporary heat is needed.

Unusual noises, a burning smell, repeated breaker trips, no heat, or visible damage at the outdoor unit all deserve prompt professional attention. Emergency Heat is a temporary backup, not a long-term solution.

Why Auxiliary Heat Can Raise Electricity Use

A heat pump normally transfers heat from the outdoor air into your home. Even when the weather feels cool, that process can be more efficient than creating heat directly with electric resistance strips. Once auxiliary heat comes on, those strips may run in addition to the heat pump, increasing your home’s electricity demand.

Thermostat habits can make an auxiliary heat thermostat activate more often than necessary. Common triggers include:

  • Raising the temperature several degrees at once
  • Using large overnight setbacks, then asking for quick morning recovery
  • Changing the thermostat setting repeatedly during the day
  • Setting the temperature much higher in hopes of faster heating

Turning the thermostat up higher does not make a heat pump heat faster. Instead, it can signal the system to bring on backup heat sooner. When practical, gradual temperature adjustments are usually easier on the system and may reduce unnecessary auxiliary heat use.

Frequent or extended backup heat can also point to a concern with airflow, equipment performance, ductwork, system capacity, insulation, or air sealing. We avoid assuming the cause without inspecting the full system.

Safe Thermostat Checks That Protect Comfort

Before arranging service, there are a few safe checks you can make. Start by confirming that your thermostat is set to Heat, not Emergency Heat. Look at the schedule as well. A deep setback may be causing the system to call for auxiliary heat each time it tries to recover.

If your system uses an air filter, check whether it is dirty and replace it as needed. Restricted airflow can affect heating performance and contribute to comfort problems. It also helps to make sure supply vents and return grilles are open and not blocked by furniture, rugs, or curtains.

Avoid trying to force a solution. Do not chip ice from the outdoor unit, open electrical panels, repeatedly reset breakers, or switch Emergency Heat on and off to troubleshoot. A light layer of frost and periodic defrosting can be normal. Heavy ice buildup, poor heating performance, or Aux Heat that seems to run constantly should be evaluated by a heat pump technician.

Pay Attention Before Backup Heat Becomes Routine

Aux Heat is often a normal part of heat pump operation during colder stretches and defrost cycles. Em Heat is different, because it bypasses the outdoor heat pump and should generally be treated as a temporary backup mode.

The useful takeaway is to watch for patterns. If your system needs Aux Heat often, cannot keep your home comfortable, or relies on Em Heat to maintain warmth, the issue deserves professional troubleshooting rather than repeated thermostat changes.

Improve Heat Pump Efficiency and Comfort

Learn how an auxiliary heat thermostat works with a properly matched heat pump system to support dependable winter comfort. Home Comfort Alliance can help assess your home’s heating needs and explain practical options for improving performance. When you are ready to discuss your system, contact us to arrange a visit with our team.