Locally-owned since 1977 • Licensed, bonded and insured in Washington (WA Contractor Reg. #HOMECCA785BD) • WA Electrical Contractor Lic. #HOMECCA782DC • NATE-certified technicians • Carrier Factory Authorized Dealer
Electrician in Monroe, WA
Our licensed electricians handle repairs, panel upgrades, EV chargers, generators and new circuits for Monroe homes. They work out of our Everett branch; call (425) 645-0404 or use the form, and a coordinator will book the visit and a time that works for you.
Monroe sits at the junction of US 2, SR 522 and SR 203, and its electricity comes from Snohomish County PUD. The city does not issue electrical permits; they come from Washington L&I (City of Monroe, When Do I Need a Permit?; L&I, cities that do their own electrical permits). We buy the permit for any job that needs one and schedule the L&I inspection.
Typical electrician costs
National estimates from Angi, electrician costs, updated August 2026. These are not Home Comfort Alliance prices; you get a written price and a permit plan before work starts.
| Job | Typical range |
|---|---|
| Service visit | $163 to $538, about $351 typical |
| Hourly rate | $50 to $130 |
| Outlet installation | $200 to $300 |
| Ceiling fan | $140 to $350 |
| Breaker box replacement | $500 to $1,800 |
| Whole-house rewiring | $1,500 to $10,000 |
Panel upgrades for growing electrical loads
Many Monroe houses built during the city’s 1990s growth have panels sized for the appliances of that time. Adding an EV charger, a heat pump, a hot tub, an induction range or a shop can push an older panel past its capacity. Signs you may need an upgrade or a load review:
- Breakers that trip when two large appliances run together.
- No open spaces left in the panel, or tandem breakers everywhere.
- A warm panel cover, a burning smell or scorch marks.
- A brand or model with a history of problems, which our electrician will point out if found.
Before recommending a new service, we run a load calculation. Sometimes a load management device or a subpanel solves the problem for much less than a full service upgrade. When a new service is needed, we coordinate the disconnect and reconnect with Snohomish PUD.
EV chargers for Monroe commuters
With SR 522 and US 2 carrying many Monroe drivers to Woodinville, Bothell, Everett and Seattle, home charging makes daily driving simple. A Level 2 charger on a 240-volt circuit typically adds a full day’s commuting range overnight. We check panel capacity, choose the circuit size to match the charger, mount it where the cable reaches without strain, and pull the L&I permit. Detached garages and long runs get a conduit plan quoted up front.
Generators and storm outages
Wind and heavy rain can bring down lines across east Snohomish County. If an outage means a cold house, a sump pump that stops, or a well pump with no water, backup power is worth planning:
- Standby generators start automatically through a transfer switch and can run the whole house or selected circuits.
- Portable generator inlets with an interlock let you plug in a portable unit safely and power chosen circuits.
Never backfeed a generator through a dryer or other outlet. It can energize utility lines and endanger line crews, and it is a fire risk in the house.
Circuits for heat pumps, water heaters and shops
A heat pump, a heat pump water heater, a hot tub or a detached shop each needs its own properly sized circuit and disconnect. When our HVAC or plumbing teams install equipment, our electricians handle the wiring so one company is responsible for the whole job. On properties outside city limits, we also wire outbuildings and upgrade circuits for well pumps.
Remodels, additions and ADUs
Kitchen and bath remodels, finished basements, additions and accessory dwelling units all change a home’s electrical needs. A kitchen alone usually needs several dedicated 20-amp circuits, GFCI and AFCI protection, and often a new range circuit. We plan the wiring with you and your contractor early, so walls are opened once, and we confirm whether the existing service can carry the new load or needs an upgrade first.
For an ADU or a detached shop, the questions are feeder size, trenching distance and whether a separate meter makes sense. We lay out the options with prices so you can decide before the ground is dug.
Surge protection and aging wiring
Modern furnaces, heat pumps, ranges and chargers all run on electronic controls that are easily damaged by voltage spikes from storms and utility switching. A whole-home surge protector installed at the panel is an inexpensive way to protect them, and it pairs well with plug-in protectors for computers and TVs.
In older sections of the home, look out for two-prong ungrounded outlets, loose outlets that no longer grip a plug, aluminum branch wiring, and DIY additions such as extension cords stapled along baseboards. None of these is unusual, and our electrician can tell you which need attention now and which can wait.
Electrical work for rebated equipment
Snohomish County PUD’s rebates for heat pumps and heat pump water heaters (Snohomish County PUD heating rebates (updated July 1, 2026); Snohomish County PUD heat pump water heater rebates) often come with electrical work: a new 240-volt circuit and disconnect for the outdoor unit, or a dedicated circuit for the water heater. Because our electricians work alongside our HVAC and plumbing teams, the wiring is priced into the same written estimate and done on the same schedule, and the rebate paperwork is handled by the team installing the equipment.
Get an estimateA comfort advisor will call you to set up your visit.
Troubleshooting, lighting and safety checks
- Dead outlets, flickering lights and breakers that will not reset.
- GFCI protection in kitchens, bathrooms, laundry areas, garages and outdoors, where wet weather makes it especially important.
- AFCI breakers, smoke and carbon monoxide alarms.
- Light fixtures, ceiling fans, recessed lighting and exterior lighting.
- Electrical inspections before buying or selling a home.
If you notice a burning smell, buzzing at the panel, or outlets that are hot to the touch, turn off the affected breaker and call us.
Buying or selling a home in Monroe
An electrical inspection before closing gives buyers a clear picture of the panel, wiring and safety devices, and gives sellers a chance to fix issues before they turn up in the buyer’s report. Our electrician checks the service and panel, looks for double-tapped breakers, missing covers, reversed polarity and missing GFCI protection, tests smoke and carbon monoxide alarms, and writes up what was found with prices for any repairs. Many items are small fixes that can be done the same day.
How an electrical visit works
- Tell us what is happening or what you want to add. Photos of the panel help.
- A licensed electrician inspects the panel and the circuit involved.
- You get a written price, including any permit, before work starts.
- We complete the work, label the panel and arrange the L&I inspection when required.
Warranty and Home Comfort Club
We support the manufacturer’s warranty on covered equipment parts, and we stand behind our electrical installations with a 1-year labor warranty from installation.
Join our Home Comfort Club, a monthly membership starting at $15 a month, and the labor warranty on repairs is extended for as long as your prepaid membership runs, up to 5 years from installation. Ask your technician or comfort advisor for the current plan details.
Monroe electrician FAQ
Who issues electrical permits in Monroe?
Washington L&I, not the City of Monroe. We buy the permit and schedule the inspection.
Who is the electric utility in Monroe?
Snohomish County PUD supplies electricity in Monroe.
How much does an electrician cost in Monroe?
National data puts a typical service visit between $163 and $538, about $351 (Angi, 2026). We give a written price before work starts.
Do I need a panel upgrade for an EV charger?
Not always. We run a load calculation first; a load management device or smaller circuit can sometimes avoid a full upgrade.
Can you install a standby generator in Monroe?
Yes. We install standby generators with transfer switches, and generator inlets with interlocks for portable units.
Is it safe to backfeed a generator through a dryer outlet?
No. It can energize utility lines and endanger line crews. Use a transfer switch or an interlock and inlet.
Can you wire a hot tub or detached shop in Monroe?
Yes. We size the feeder or circuit, install the disconnect and GFCI protection, and pull the L&I permit.
Do you install whole-home surge protection?
Yes. A surge protector at the panel helps protect furnaces, heat pumps and other electronics from voltage spikes.
What warranty comes with your work?
We support the manufacturer’s warranty on covered equipment parts, and our labor warranty covers installations for 1 year from installation. Home Comfort Club members (monthly membership starting at $15 a month) get the labor warranty on repairs extended for as long as their prepaid membership runs, up to 5 years from installation.
Why Choose Home Comfort Alliance in Monroe?
Your Comfort is Our Promise
We promise...
Reliable heating, air conditioning, plumbing and electrical service, all from one trusted company.
To educate and guide you through your options so you’ll find the right solution at the right price.
Knowledgeable and respectful workers who ensure both your own comfort during the installation process, and lasting comfort from your home systems.
Outstanding service, communication, and follow-up, so your home is comfortable now and for years to come.
Get an electrical estimate in Monroe
An Everett-based coordinator will book a licensed electrician, and you get a written price and permit plan before work starts.
Get an estimate
An Everett-based comfort advisor will call you to set up your visit.