Furnace Repair in Silverdale, WA
Gas and electric furnace repair for Silverdale and Central Kitsap from our Bremerton team: fees listed up front and a written price before work starts.
Locally-owned since 1977 • Licensed, bonded and insured in Washington (WA Contractor Reg. #HOMECCA785BD) • NATE-certified technicians • Carrier Factory Authorized Dealer • Mitsubishi Electric Diamond Dealer
Silverdale furnace repair, the short answer
Home Comfort Alliance repairs gas and electric furnaces in Silverdale, WA, from our Bremerton branch about 9 miles away, with an upfront price before any work begins. You pay a $119 trip fee and $72 to find the fault, then see the repair price in writing; work starts only when you say yes.
Call (425) 645-0404. Our phones are answered and bookings are accepted 24/7. You can also send the request form at the bottom of the page and we will call you back.
Smell gas? Cascade Natural Gas serves Silverdale. Get everyone outside, then phone Cascade at 1-888-522-1130 or 911 (Cascade emergency steps). We can come out after Cascade says the house is safe.
Furnace repair prices in Silverdale
The Bremerton branch uses one price list for all of Central Kitsap, so a Silverdale call costs the same as one in Bremerton itself.
| Home Comfort Alliance item | Price |
|---|---|
| Dispatch (trip) fee | $119 |
| Standard diagnostic | $72 |
| Deeper diagnostic (when needed) | $130 |
| After-hours fee (qualifying emergencies) | $330 |
| Ignitor replacement | $353 to $821 |
| Thermostat replacement | $299 to $1,840 |
| Furnace tune-up | $230 ($180 for Home Comfort Club members) |
Prices as of October 2026. You pay for one diagnostic level, not both.
Outside benchmark, not our price: Angi's Seattle-area estimate (August 2026) puts most furnace repairs at $139 to $544, with an average of $341 (Angi furnace repair costs).
This season's offers: $50 Off Emergency No Heat Calls, or $50 off HVAC service or repair (special offers; not combined with Club pricing). If a big repair lands at a bad time, plans through Salal Credit Union or Synchrony start at $179/month* (financing).
*Financing through Salal Credit Union or Synchrony, subject to credit approval. Rates, terms and monthly payments depend on the amount financed, the plan and your credit. 0% interest options are available to qualifying customers. See lender for full terms.
Get an estimateA written, upfront price before any work begins.
No heat in Silverdale? Five checks before you call
- Set the thermostat to HEAT, a few degrees above room temperature, and put in fresh batteries. A weak battery can stop the call for heat while the screen still lights.
- Make sure the switch beside the furnace and the furnace breaker in the panel are both on.
- Pull the filter. A clogged filter can overheat the furnace and trip its limit switch.
- Press the lower furnace door fully closed. An open door cuts power on purpose.
- On a high-efficiency furnace, check the white plastic drain line for a kink or a full trap.
If the house is still cold, write down the blink pattern from the little light on the control board; it tells our technician where to start. There is a fuller checklist in our furnace won't turn on article.
Signs your furnace needs repair
- The draft fan starts, then everything stops before the burners light.
- Clicking or a glowing ignitor with no flame, then a lockout after a few tries.
- Cool air from the registers during a heating cycle.
- Short cycling: a few minutes on, off, then on again.
- Rooms that never warm up, even with every door open.
- A burning, electrical or rotten-egg smell. Treat a gas odor as a safety issue first.
- New bangs, squeals or rattles, or a Cascade or PSE bill that jumps for no reason.
Kitsap's damp winters keep furnaces running for long stretches from October to April, so a weak ignitor, a dirty flame sensor or a tired blower capacitor tends to show up in the first cold week.
Common furnace repairs we make in Silverdale
| What you notice | Usual cause | What we do |
|---|---|---|
| Ignitor glows, no flame | Gas valve, flame sensor or gas pressure | Measure voltage at the valve and gas pressure; clean or replace the failed part |
| Clicks, no glow | Ignitor | Test resistance; replace (ignitor replacement $353 to $821) |
| Starts, then shuts down | Pressure switch, inducer or venting | Check draft, hoses and the vent path; repair the cause |
| Blows cold air | Limit switch tripped by low airflow | Check filter, blower and ducts before any reset |
| Weak airflow or a humming blower | Blower capacitor, motor or a dirty wheel | Measure the capacitor against its rating and the motor's amp draw |
| Water near the furnace | Blocked condensate trap or drain | Clear and reroute the drain line |
| Blank or erratic thermostat | Batteries, wiring or a failed thermostat | Test the low-voltage circuit; thermostat replacement $299 to $1,840 if needed |
Our NATE-certified technicians work on every major furnace brand, and Home Comfort Alliance holds Lennox Premier and Carrier Factory Authorized dealer status.
Gas smell or a carbon monoxide alarm: what to do
Get everyone out first. Do not flip switches, start a car in an attached garage or use a phone inside. From outside, call Cascade Natural Gas at 1-888-522-1130 or 911 for a gas odor, and 911 for a carbon monoxide alarm. Once the utility or fire department clears the home, call us and we will find the cause. We check carbon monoxide on every gas furnace call.
Repair or replace your furnace?
A single bad part on a younger furnace is almost always a repair. The picture changes with age and repeat visits: if the furnace is near 15 years old, has needed several fixes, or has a cracked heat exchanger, get a replacement price next to the repair price. A common shortcut is the $5,000 rule: multiply the furnace's age by the repair quote, and if the result tops $5,000, compare both options.
If you do replace a gas furnace in Silverdale, Cascade Natural Gas pays $1,600 for a 95% AFUE furnace and $2,400 for 98% AFUE, plus $150 for a qualifying thermostat and $1,000 for duct sealing, on installs from March 15, 2026, in homes heated mainly by gas (Cascade 2026 to 2027 rebate list). Furnaces under 95% AFUE do not qualify. We are a Cascade-listed contractor and file the rebate for you. Repairs earn no rebate.
A replacement estimate costs nothing, and the instant HVAC quote tool shows a price range in about 30 seconds. Most furnace installations take between 4 and 10 hours. What you get with a replacement: a 3-year Comfort Shield labor warranty on new installations, kept active with yearly maintenance. First-year maintenance is included. See furnace replacement in Silverdale.
Hours and after-hours help
Our phones are answered and bookings are accepted 24/7. Heating and cooling technicians work during business hours and are available after hours for qualifying emergencies ($330 after-hours fee), such as no heat in cold weather or a burning or electrical smell.
Regular appointments are Monday to Friday, 8 AM to 5 PM, and we fit in same-day calls when the schedule allows. Waiting for morning? Keep interior doors closed to hold heat in the rooms you use, give any portable heater three feet of clear space, and never use a stove, oven or grill to warm the house.
How a Silverdale repair visit works
- Call or book online; we give you a time window, not just a day.
- A NATE-certified technician drives up from our Bremerton office.
- The technician reads the fault code, then watches the furnace run one full cycle from the thermostat call to the blower.
- We test the safety switches, gas pressure, temperature rise and venting, and check carbon monoxide.
- You see the written price and decide. Our trucks are fully stocked, so most repairs can be handled on the spot.
- After the repair, the furnace runs again while the technician explains what would signal a return visit.
Permits and utilities in Silverdale
Silverdale is unincorporated Kitsap County, so permits come from the county, not a city. Puget Sound Energy supplies electricity and Cascade Natural Gas supplies natural gas.
Kitsap County's Department of Community Development requires a mechanical permit for furnace work except appliance repair, so a part repair normally needs none, while replacing a furnace does (Kitsap County permit guide). Electrical permits come from Washington L&I. We pull the required permits for every installation.
Moving in or out with a Naval Base Kitsap-Bangor assignment? Book a furnace check early in the move window so any repair is done before the first cold night.
A recent Silverdale no-heat call: a furnace that would not light
In October a new customer in Silverdale called because a Carrier gas furnace had stopped heating. When the thermostat called for heat, the furnace started up, but the burners never lit.
Our technician found a weak blower capacitor, rated 7.5 microfarads and measuring 6.14, and a dirty blower assembly. On his test cycle the draft fan started, the pressure switch closed, the ignitor glowed and the burners lit. Gas pressure was running at 4 inches of water column, so he set it back to 3.4, and the temperature rise of 26°F sat inside the furnace's 20 to 50°F range. Because the failure was intermittent, he left a written estimate for an ignition and fan control board in case it returns.
From our October 2026 service records; customer details are kept private.
Why Silverdale homeowners call us
- A posted price list and a written quote before work starts.
- TrustAnalytica Top 10 HVAC Contractor 2026 (Bremerton).
- NATE-certified technicians from our Bremerton office, 5373 Auto Center Way, Suite 205.
- Licensed, bonded and insured in Washington: WA Contractor Reg. #HOMECCA785BD and WA Electrical Contractor Lic. #HOMECCA782DC.
- Lennox Premier Dealer, Carrier Factory Authorized Dealer and Mitsubishi Electric Diamond Dealer; all major brands serviced.
- BBB Accredited Business since 2002, ACCA member, Best Pick 2025 and 2026.
- Home Comfort Club plans from $15 a month with a yearly tune-up and member pricing (membership plans).
- Locally owned since 1977.
Where we repair furnaces around Silverdale
We repair furnaces throughout Silverdale, ZIP codes 98383 and 98315, from our Bremerton branch. If your system is a heat pump, see heat pump repair in Silverdale, and for every service we offer here, see Silverdale HVAC, plumbing and electrical.
Silverdale furnace repair FAQ
How much does furnace repair cost in Silverdale?
A repair visit carries a $119 dispatch (trip) fee, and diagnosis is $72 for a standard diagnostic or $130 for a deeper one. After-hours visits for qualifying emergencies carry a $330 after-hours fee. You get a written, upfront price before any work begins. For context, Angi lists Seattle-area furnace repairs at $139 to $544 (August 2026); that is not our price.
Do I need a permit to repair my furnace in Silverdale?
Kitsap County requires a mechanical permit for furnace work except appliance repair, so a part repair normally needs none. Replacing a furnace needs a Kitsap County permit, and electrical permits come from Washington L&I. We pull the required permits for every installation.
What should I do if I smell gas?
Leave the home, do not use switches or phones inside, and call Cascade Natural Gas at 1-888-522-1130 or 911 from outside. Once it is safe, call us.
Can you come today or after hours?
Same-day service when possible. Our phones are answered and bookings are accepted 24/7. Heating and cooling technicians work during business hours and are available after hours for qualifying emergencies ($330 after-hours fee), such as no heat in cold weather.
Why is my furnace blowing cold air?
Common causes are a dirty flame sensor or a weak ignitor that stops the burners, a clogged filter that trips the limit switch, a blocked condensate drain on a high-efficiency furnace, or a thermostat fan set to ON instead of AUTO.
Why does my furnace turn on and off quickly?
Short cycling usually comes from a dirty flame sensor, an overheating furnace behind a clogged filter, a blocked vent or drain, or a thermostat in the wrong spot. A diagnostic finds which one.
How much does an ignitor replacement cost?
Ignitor replacement is $353 to $821 at Home Comfort Alliance, plus the visit fees.
Should I repair or replace my furnace?
One failed part on a furnace under about 15 years old is usually worth fixing. The $5,000 rule (age times repair cost) is a rule of thumb for when to compare. We give you the repair price first, and replacement estimates are free.
Are there rebates for furnace repair in Silverdale?
No. Replacing with a 95% AFUE or better gas furnace can earn a Cascade Natural Gas rebate of $1,600, or $2,400 at 98% AFUE, on installs from March 15, 2026; we handle the paperwork.
How long does a new furnace take to install?
Most furnace installations take between 4 and 10 hours.
Do you service my furnace brand?
Yes, all major brands. Home Comfort Alliance is a Lennox Premier Dealer and a Carrier Factory Authorized Dealer.
Is Home Comfort Alliance licensed?
Yes. WA Contractor Reg. #HOMECCA785BD and WA Electrical Contractor Lic. #HOMECCA782DC. Licensed, bonded and insured in Washington, NATE-certified technicians, locally owned since 1977.
Why Choose Home Comfort Alliance in Silverdale?
Your Comfort is Our Promise
We promise...
Reliable heating, air conditioning, plumbing and electrical service, all from one trusted company.
To educate and guide you through your options so you’ll find the right solution at the right price.
Knowledgeable and respectful workers who ensure both your own comfort during the installation process, and lasting comfort from your home systems.
Outstanding service, communication, and follow-up, so your home is comfortable now and for years to come.
Book a furnace repair in Silverdale
Tell us what the furnace is doing. Describe the problem and a Bremerton heating technician will diagnose it and quote the repair in writing before starting.
Request furnace repair
We will call you to set up the visit. For no heat after hours, call (425) 645-0404.